**Get it on Cults3D here ->** https://cults3d.com/en/3d-model/gadget/headphone-rest-v3-for-notebooks-laptops

The goal of my design is to create some kind of **rest or hook for a headphone / headset** while you are working on your notebook/laptop.
My headphone was always laying arround and i wanted a cleaner desk.

The headphone rest have to be **placed / double tape glued onto the backcover of the notebook/laptop**.

The headphone rest **can be slided out to hang on your headset** to the hook and if you put your notebook/laptop in a bag for travel etc.. you can just simply slide the rest in.

The **example pictures** will show you where to place it and how to use it :)

**If you like my design, i would appreciate it if you buy it to support me for my time to create it and make future designs possible.**

**Note:** Double side tape - i used a 0.8mm thin double sided tape with a width of 30mm (which fits perfect for the design), you may use a 3M or a similar tape from amazon, aliexpress, local store etc.

Befor you glue it onto the notebook/laptop - make sure both have temperatures > 20°C and the spot where you tape it onto the notebook/laptop is free of dirt, dry and cleaned (like with isopropylalcohol ...) to get a nice bond. (Make sure you do not damage the backcover by the material used).

If you like the design, you can fill out the offset surfaces with a white/colored waterproof pencil to give it a highlight.

**Print settings:**
Print material: PETG (recommended)
Nozzle size: 0.4mm
Layer height: 0.16mm or 0.12mm works perfect. (maybe 0.2mm works too, but i have not tested it since the parts are small)
Print duration: 1 set (base + slider) was 42min on my Prusa MINI+

**Postprocessing:**
- Place the double sided tape on the back of the base
- Put a very very small dip of grease / oil onto the "inner rails" of the base
- Connect the slider into the base with a little force to "snap in"
- Try to move the slider from side to side, if it runs smooth all good, if not, maybe a little sanding/mechanical smoothing is needed.

**Get it on Cults3D here ->** https://cults3d.com/en/3d-model/gadget/headphone-rest-v3-for-notebooks-laptops


Headphone Rest - v3 (for Laptop, Notebook)

The goal of my design is to create some kind of rest or hook for a headphone / headset while you are working on your notebook/laptop.
My headphone was always laying arround and i wanted a cleaner desk.

The headphone rest have to be placed / double tape glued onto the backcover of the notebook/laptop.

The headphone rest can be slided out to hang on your headset to the hook and if you put your notebook/laptop in a bag for travel etc.. you can just simply slide the rest in.

The example pictures will show you where to place it and how to use it :)

If you like my design, i would appreciate it if you buy it to support me for my time to create it and make future designs possible.

Note: Double side tape - i used a 0.8mm thin double sided tape with a width of 30mm (which fits perfect for the design), you may use a 3M or a similar tape from amazon, aliexpress, local store etc.

Befor you glue it onto the notebook/laptop - make sure both have temperatures > 20°C and the spot where you tape it onto the notebook/laptop is free of dirt, dry and cleaned (like with isopropylalcohol ...) to get a nice bond. (Make sure you do not damage the backcover by the material used).

If you like the design, you can fill out the offset surfaces with a white/colored waterproof pencil to give it a highlight.


Print material: PETG (recommended)
Nozzle size: 0.4mm
Layer height: 0.16mm or 0.12mm works perfect. (maybe 0.2mm works too, but i have not tested it since the parts are small)
Print duration: 1 set (base + slider) was 42min on my Prusa MINI+

Postprocessing:
- Place the double sided tape on the back of the base
- Put a very very small dip of grease / oil onto the "inner rails" of the base
- Connect the slider into the base with a little force to "snap in"
- Try to move the slider from side to side, if it runs smooth all good, if not, maybe a little sanding/mechanical smoothing is needed.

**Update V2+V3!**

**You can get the new version with alot of improvements on Cults.**
[https://cults3d.com/en/3d-model/various/creality-ender-3-v2-fan-cover-duct](https://cults3d.com/en/3d-model/various/creality-ender-3-v2-fan-cover-duct)

cheers!




----------

Model originally uploaded to Thingiverse at https://www.thingiverse.com/thing:5331687.

----------


This is a replacement for the stock hotend fan case / housing / cover since they break alot on the front fan screws.

I've made this to print out of a single part with no supports but still keep the design of the stock one. The fans inside + the radial fan airflow piece can still be used in this cover as well. 

Take care about the 2 small pins on the side to not break them since they are used to align the radial fan airflow piece.

I recommend to print in PETG and befor the first mount to drill out the boreholes for the screws to prevent cracking of them (some possible filament left in there from printing).

If you like my design, you can send me a tip above to pay off the coffee while i made this.

THE FREE MODEL YOU CAN DOWNLOAD HERE MIGHT NOT FIT SINCE IT WAS A FIRST TEST PRINT MODEL!!! YOU SHOULD GET THE CURRENT MODEL FROM CULTS3D!!!

Ender 3V2 Hotend Fan Cover Housing Duct

Remix of Marsgizmo Filament Bunker v3 - Silica Lid

Improved some corners and the grid for smoother and faster printing + a little bit more stability.

https://thangs.com/designer/marsgizmo/3d-model/marsgizmo-Filament-Bunker-V2-12690

Marsgizmo Filament Bunker v3 - Lid_rev2.stl

Remix of Marsgizmo Filament Bunker v3 - Silica Lid

Improved some corners and the grid for smoother and faster printing + a little bit more stability.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

e-soni

Headphone Rest - v3 (for Laptop, Notebook)

Ender 3V2 Hotend Fan Cover Housing Duct

Marsgizmo Filament Bunker v3 - Lid_rev2.stl