Hi all,

i'm back with a wall art wit open top layer design. This desings are made for printin on all printers.

More of this Pokémon hexagon are coming soon.

COMMERCIAL USE
For personal: https://makerworld.com/en/@Kevyn3D

Bambu Studio orcaslicer - Instruction for the open top layer: The screenshots are from a other model but the steps ar the same (attached PDF), only some parameters changes.  (the setting are set in the 3mf)

-In global tab choose the Octogram Spiral infill en enable supports
-Go the the object tab; i used the Height range modifier (Right click on the object in the object tab)
That way Pikachu have closed top layer

Choosing other infill is also possible (Archimedean Chord did'nt work for me)

Set the layes you want to change; in this case it's 0 to 15 mm

In the object tab set top layers to 0 and infill to Octogram Spiral

Dont forget to do the color swaps.

Start with yellow

at layer 75 change to black

at layer 79 change to yellow

at layer 82 change to red

at layer 85 change to white

At layer 88 to black

Have fun printing, and don't hesitate to share your makes.

Also go check my other models.

COMMERCIAL USE
For personal: https://makerworld.com/en/@Kevyn3D

Pikachu Hexagon Wall art

Pikahex.stl

** commercial use ONLY**
I was thinkering on something fun and walked by the fridge. Imagine have some plant magnets, but with real plants. You can also use them to put something else in it 

This small planters for plants with a diamer of 54mm and a height of 52mm.

At the back are two inserts for magnets 3x10 (my magnets are 2.7mm thick; once they are glued is, they are deeper and it's not possible to have scratches on the fridge.

Pinting is easy, no suppors needed.
Check also my other models

 Fridge magnetic planter for succelent plants - 1

Pot.stl

** commercial use ONLY**
I was thinkering on something fun and walked by the fridge. Imagine have some plant magnets, but with real plants. You can also use them to put something else in it

This small planters for plants with a diamer of 54mm and a height of 52mm.

At the back are two inserts for magnets 3x10 (my magnets are 2.7mm thick; once they are glued is, they are deeper and it's not possible to have scratches on the fridge.

Pinting is easy, no suppors needed.
Check also my other models



Fridge magnetic planter for succelent plants - 2

Pot2v1..stl

Fridge magnetic planter for succelent plants - 3

po1v1.stl

I designed the wall art puzzle with a Star Wars Theme. Total size is 40x40cm and i fixed it with double sided tape.

COMMERCIAL USE
For personal: https://makerworld.com/en/@Kevyn3D

The white with black top gives a cool effect, i looks like silver. The color change is al layer 100

_Instruction for the open top layer: _ Bambu Studio (the setting are set in the 3mf (Bambu Studio))

In global tab choose the Octogram Spiral infill en enable supports Go the the object tab; i used the Height range modifier (Right click on the object in the object tab) That way the logo and symbols have a closed top layer Choosing other infill is also possible
-Set the layes you want to change; in this case it's 0 to 20 mm

-In the object tab set top layers to 0 and infill to Octogram Spiral

-Dont forget to do the color swaps. Change at layer 100 to the color of your choice

Slice and print =)

Have fun printing, and don't hesitate to share your makes.

Also go check my other models.

Not for commercial use

Star Wars Puzzle - Wall Art

puzzle4.stl

puzzle2.stl

t's almost valentine, so it's time for some real love. That's why i designed this shadow box, and you know what? The best thing to hold on in life is each other. So keep enjoying each other every day. oh, you know it's real love when forever is not long enough.

Colors needed: red, pink, white and black. But you can choose your own colors. 

I added a 3MF for Bambu printers. No AMS needed.

[https://youtu.be/GKEen7c8o2A](url)

You can put a light at the back, so the small hearts lights up
Go check my other models and don't forget to share your makes;,

Valentine Shadow box

fullplate.stl

Fast and easy print with the AMS with 4 colors

Printed by prefence on a structured PEI plate, all plates are facing down in the 3mf file, so you have the structure of the PEI on the print, what is nicer. But of course the way how you put the slices in the holder, is your own choice :) - All my shadow boxes ar compatible with each other.

Instruction:
3MF file is ready to print.
all other files are 7 different plates - add them as 1 file

Plate 1: 
-EeveeBlack.stl
-EeveeBody.stl
-EeveePink.stl
-EeveeWhite.stl

Plate2:
-backgroundbird.stl
-birdsblack.stl

Plate 3:
-sand.stl

Plate 4:
-PikaWeed.stl

Plate 5:
-Pikagrass.stl

Plate 6: 
-Pikaclouds.stl

Plate 7:
-holdelonger side.stl
-holdercap.stl




Eevee Pokemon Shadowbox - multicolor

EeveeShadowbox.3mf

Fast and easy print with the AMS with 4 colors

Printed by prefence on a structured PEI plate, all plates are facing down in the 3mf file, so you have the structure of the PEI on the print, what is nicer. But of course the way how you put the slices in the holder, is your own choice :) - All my shadow boxes ar compatible with each other.

Instruction:
3MF file is ready to print.
all other files are 4 different plates
Plate1:
- Fire2Orange.stl
- Fire2Red.stl

Plate 2:
-CharizardBellyYellow.stl
-CharizardBlack.stl
-CharizardWings.stl
-CharzardOrange.stl

Plate 3:
-FireOrange.stl
-FireYellow.stl

Plate 4:
-CharizardTailBlack.stl
-CharizardTailOrange.stl
-CharizardTailRed.stl
-CharizardTailYellow.stl

Plate 5:
- Back.stl

Plate 6:
-holdelonger side.stl
-holdercap.stl



Have fun printing them en go check my other models.

Charizard Shadow box - multi color

CharizardBlack.stl

Hi Fan

If you love what i do, and just want to support me… you’re on the correct tier.

With this i’m able to continue creating content and models.

You will get early acces to models a few days before they release on other platforms.

This tier does not give a commercial license.

Thanks to be a member!

Fan Base

Hello 3D print ethousiast

Thanks for considering a membership for commercial License

You will get early acces to models a few days before they release on other platforms

Please note the following:
- All files, also the free files on my page can be used for commercial license.
Some of them ar member exclusive
- The digital files are NOT for resale or distribution. 
- Commercial license is only given to active members. If you choose to cancel your membership your commercial license will end at the time the membership is canceled.


Commercial use license

Puzzle3.stl

Puzzle1.stl

Hi all,

i'm back with a wall art wit open top layer design. This desings are made for printin on all printers.

More of this Pokémon hexagon are coming soon.
 
COMMERCIAL USE
For personal: https://makerworld.com/en/@Kevyn3D

Check Pickachu [HERE](https://thangs.com/designer/Kevyn3D/3d-model/Pikachu%20Hexagon%20Wall%20art-1048766)

Bambu Studio or orcaslicer - Instruction for the open top layer: The screenshots are from a other model but the steps ar the same (attached PDF), only some parameters changes. (the setting are set in the 3mf)

-In global tab choose the Octogram Spiral infill en enable supports
-Go the the object tab; i used the Height range modifier (Right click on the object in the object tab)
That way Pikachu have closed top layer

Choosing other infill is also possible (Archimedean Chord did'nt work for me)

Set the layes you want to change; in this case it's 0 to 15 mm

In the object tab set top layers to 0 and infill to Octogram Spiral

Dont forget to do the color swaps. for the green i used Bambu PLA-CF green, cause i like the color. But light green colors should do the trick.

Start with Orange

at layer 75 change to black

at layer 79 change to green

at layer 82 change to orange

at layer 85 change to yellow

Go also check my other models
FOR COMMERCIAL USE

Charizard Hexagon Wall Art - Pokemon

ChariHex.3mf

Charihex.stl

Hi all

Every year we give flowers to our mom; but flower wither al the time. So i was thinking to make some useful flowers, that don't need water.

But only flowers would be boring, so i made them magnetic and that way it's possible to use them on your fridge or other magnetic surfaces.

The flower are designed that a AMS is not needed, the colors can be changed with manual color changes. (instruction below)

Offcourse you can choose your own colors for the flowers.

The plate with the stems can be printed without support, but make sure that bridging is enabled.

 

The magnets i used are diameter 10mm x 3mm thick. The holes in the stems are 3mm deep on the flowers 1.5mm, that for easy removal when used on flat surfaces. Use strong glue and check the polarities

 

Magnets: 10mmx3 Magnets on amazon

Colorchanges by plate (choose your own favorite colors)

Plate 1 - Flowermagnet.stl (3 colors)

Start with color of your choice

1st change at layer 11

2nd change layer 14

 

Plate 3 - Flowermagnet2.stl (4 colors)

Start with color of your choice

1st change at layer 11

2nd change at layer 14

3th change at layet 17

 

Plate 4 - Flowermagnet3.stl (4 colors)

Start with color of your choice

1st change at layer 11

2nd change at layer 14

3th change at layet 17

 

Plate 5 - Flowermagnet5.stl (3colors)

Start with color of your choice

1st change at layer 11

2nd change at layer 14

 

Plate 6 - Flowermagnet4.stl (3 colors)

Start with color of your choice

1st change at layer 11

2nd change at layer 14

 

Plate 7 - Flower holder - optional (2 colors)

Start with red (i used silk red from esun)

Change at layer 203 to white

 

Dont forget to share your makes and check my other models.

Magnetic memo flowers

MotherFlowers (1).3mf

flowerholder.stl

magnetflower5.stl

Flowermagnet4.stl

Steelleaffull.stl

steelleaf.stl

Flowermagnet3.stl

flowermagnet2.stl

steel.stl

Flowermagnet.stl

Hi All
This simple game can be played by all ages (6-99+ recommended) it's based on OK Plat  or Cinco Linco.

Printing: print 4x16 in 4 colors; Make the tiles cooler by adding a color change at layer 10.
The holder and the cap just prints with a 15-20% infill; make sure the cap is laying withe flat side down.
The holes fits magnets 5mm x 1mm. Just press fit should work;

The rules are simple, the game is playable with 2-4 players. Each player choose a color, if you are playing with 2 than you choose 2 colors each. Each players have to try to make a line of 5. Tiles can only be placed verticaly or horizontaly, side by side. The first person that makes 5 in a row wins the party. If all tiles ar used and there is no winner, the tiles can be replaced one by one untill there is a winner

Have fun playing

Commercial licence with the Commercial Licence [membership](url)


OK3D - Family game - Based on OK play & Cinco Linco

Oke3Dtile.stl

Oke3DHolder.stl

oke3Dcap.stl

I'm a 3D printfluencer with a passion for 3D printing.
I started printing during the first covid lockdown. I learned myself to work with some designing software.

You can find me an tiktok, instagram and youtube where i make fun content around 3D printing.

Activity related to collaborating with others on models

Likes, comments, and activity from your community

A roundup of models that we think you'll like

For when we think someone might have posted your content as their own

New content from your premium memberships

Emails and messages from designers you follow

Kevyn3D

Pinned models

Star Wars Puzzle - Wall Art

Charizard Hexagon Wall Art - Pokemon

Magnetic memo flowers

OK3D - Family game - Based on OK play & Cinco Linco

Pikachu Hexagon Wall art

Fridge magnetic planter for succelent plants - 1

Fridge magnetic planter for succelent plants - 2

Fridge magnetic planter for succelent plants - 3

Star Wars Puzzle - Wall Art

Valentine Shadow box

Eevee Pokemon Shadowbox - multicolor

Charizard Shadow box - multi color